What Is the FitGo Dial Lacing System and Is It Worth It?
Laces snap, come undone and get caked in mud, and doing them up with cold hands or thick gloves is nobody's favourite job. The FitGo dial lacing system is designed to solve all of that with a simple twist. This guide explains what FitGo is, how it works, and whether a FitGo boot is worth choosing over traditional laces.
| Quick answer: FitGo is a dial-based lacing system: you turn a dial to tighten a fine, strong cable evenly across the boot, and lift or pull the dial to release it in one motion. It gives a quick, precise, even fit with no laces to tie, snag or trip over. It is well worth it if you value speed, convenience and a consistent fit, especially when wearing gloves. See our FitGo boots range. |
What is the FitGo dial lacing system?
FitGo replaces traditional laces with a dial and a thin, high-strength cable that runs through guides across the boot. Instead of threading and tying laces, you simply turn the dial to draw the cable tight, and the boot closes evenly around your foot. It is the same idea as the dial systems you may have seen on cycling shoes and snowboard boots, brought to safety footwear where a fast, secure and reliable fit really counts.
How does FitGo work?
Using FitGo takes seconds and follows three simple steps.
- Turn to tighten. Slip the boot on and turn the dial. Each click draws the cable in a little more, tightening the boot evenly from bottom to top.
- Fine tune. Keep turning until the fit feels secure and comfortable. Because the cable pulls evenly, you avoid the tight and loose spots you get from laces.
- Lift to release. At the end of the day, lift or pull the dial and the cable releases instantly, so the boot loosens in one motion for an easy exit.
The benefits of FitGo dial lacing
- Fast on and off: tighten and release in seconds, with no laces to tie.
- Even, precise fit: the cable spreads pressure evenly, avoiding hot spots and pinch points.
- Glove friendly: easy to operate with cold hands or work gloves on.
- No trailing laces: nothing to come undone, snag on machinery or trip you up.
- Micro-adjust on the move: nudge the dial during the day if your foot swells or you want it tighter.
Are there any downsides?
FitGo is not for everyone, and it is fair to weigh the trade-offs. A dial system is a mechanical part, so in theory there is more to go wrong than with a simple lace, though quality dials are hard-wearing and the cable and dial can usually be replaced if needed. FitGo boots also tend to sit at a slightly higher price point than basic laced boots. And some people simply prefer the familiar feel and infinite adjustability of traditional laces. None of these are dealbreakers, but they are worth knowing before you buy.
Is FitGo worth it?
For most people who try it, yes. If you take your boots on and off often, work in gloves, struggle with laces, or just want a secure fit you can set and forget, the convenience quickly pays for itself. If you rarely change your boots during the day and are happy with laces, the benefit is smaller. As a rule, the more often you adjust or remove your boots, the more you will appreciate FitGo. Browse the FitGo range to see the styles, including lighter safety trainers and the latest new arrivals.
Who is FitGo best for?
- Workers who put boots on and off many times a day
- Anyone who wears gloves and finds laces fiddly
- People who want an even, no-pressure-point fit
- Those who have struggled with laces coming undone on site
FitGo vs traditional laces
Both do the same job of holding the boot to your foot, but they suit different priorities.
| Feature | FitGo dial | Traditional laces |
|---|---|---|
| Speed on and off | Seconds, in one motion | Slower, tie and untie |
| Fit | Even, no pressure points | Adjustable but can be uneven |
| With gloves | Easy to operate | Fiddly with cold hands |
| Trailing laces | None | Can snag or come undone |
| Cost | Usually higher | Lower |
| Familiarity | Newer system | Familiar to everyone |
Does FitGo hold up on site?
A fair question about any moving part is whether it survives real work. Modern dial systems are built for exactly this, using tough housings and steel-cored cables designed to shrug off dust, water and knocks, and the cable sits close to the boot rather than flapping loose where it could catch. No system is indestructible, but for most trades a quality dial is every bit as dependable as a lace, with the bonus that it will not work loose halfway through a shift. If a part does fail, it is usually a quick, low-cost replacement rather than a new pair of boots.
How to look after your FitGo boots
FitGo needs very little maintenance. Keep the dial and cable guides free of thick mud and grit so the cable runs smoothly, release the cable fully before pulling the boots off to avoid straining it, and store the boots with the cable loosened. If the cable or dial is ever damaged it can usually be replaced rather than writing off the boot, so check the product and warranty details. The rest of the boot cares for like any other, with regular cleaning and drying.
FitGo across the range
FitGo is not limited to one style. You will find the dial system on rugged S3 boots for outdoor and site work, on lighter safety trainers for warehouse and indoor roles, and on waterproof styles for wet conditions, so you get the convenience of a dial without giving up the protection your job needs. New options usually appear first in our new in range.
Getting the best from your FitGo boots
A couple of habits help you get the most from a dial system. When you first put the boots on, tighten from the toe end upward so the fit settles evenly, then add a final click or two once you have walked a few steps and the boot has moulded to your foot. If your feet swell during the day, a small extra turn restores the fit in seconds, and a quick release at breaks lets your feet recover. Small adjustments like these are exactly what a dial makes easy, and they are far quicker than stopping to retie a lace.
Frequently asked questions
How does the FitGo dial system work?
You turn the dial to tighten a fine cable evenly across the boot, and lift or pull the dial to release it in one motion. There are no laces to thread or tie, and the fit stays even and secure.
Is FitGo better than laces?
It depends on your needs. FitGo is faster, more even and glove friendly, with no trailing laces. Laces are cheaper, familiar and infinitely adjustable. If you take your boots on and off often, FitGo usually wins.
What happens if the FitGo dial breaks?
Quality dial systems are hard-wearing, and the dial and cable can usually be replaced rather than writing off the boot. Check the specific product and warranty details before you buy.
Can you use FitGo boots with gloves?
Yes, and it is one of the biggest advantages. A dial is far easier to turn with cold hands or work gloves than tying and untying laces, which makes FitGo popular for outdoor and winter work.
Similar Blogs
FITGO vs Laces: Are Dial-Fastening Safety Boots...
Quick answer: FITGO is a dial-fastening system that tightens a safety boot with a quick turn of a dial instead of laces, giving a fast, even, precise fit that will...
FITGO vs Laces: Are Dial-Fastening Safety Boots...
Gore-Tex and Waterproof Membranes in Work Boots...
Quick answer: A waterproof membrane is a thin, breathable barrier bonded inside the boot that stops water getting in while letting sweat vapour escape. GORE-TEX is the best known membrane,...
Gore-Tex and Waterproof Membranes in Work Boots...
Are Leather Safety Boots Waterproof? What to Ex...
Quick answer: Leather is naturally water-resistant but not fully waterproof on its own. A leather safety boot only keeps feet properly dry when it is built with a waterproof membrane...